diff --git a/FEATURES.md b/FEATURES.md
index 162ae1a..b26bf55 100644
--- a/FEATURES.md
+++ b/FEATURES.md
@@ -33,7 +33,7 @@ dedicated PLAN.md phase (or fold it into the relevant existing work) and mark it
 | FEAT-11 | `SHIPPED` | Hotspot SSID/password settings + 5GHz WiFi role swap | Phase 27 |
 | FEAT-12 | `SHIPPED` | Log OBD speed before GPS fix (rolling-start capture) | Phase 27 |
 | FEAT-13 | `IDEA` | Flush uploaded tracking rows from local DB | unassigned |
-| FEAT-14 | `IDEA` | Second T3U to replace onboard wlan0 (dual AC radios) | unassigned |
+| FEAT-14 | `SHIPPED` | Second T3U to replace onboard wlan0 (dual AC radios) | Phase 29 |
 | FEAT-15 | `SHIPPED` | Clear DTC codes from the DTC page | Phase 29 |
 
 ---
@@ -259,21 +259,22 @@ dedicated PLAN.md phase (or fold it into the relevant existing work) and mark it
 
 
 ### FEAT-14 — Second T3U to replace onboard wlan0 (dual AC radios)
-- **Status**: `IDEA`
-- **Area**: hardware + `deploy/yaris_uplink.py`, `deploy/install_netwatch.sh`, `modules/app_network.py`
-- **Phase**: unassigned
-- **What**: Owner bought a second TP-Link Archer T3U (RTL8812BU) to replace the onboard
-  BCM43438 currently serving as the internet uplink (wlan0). Both radios would then be fast
-  AC1300 T3U dongles — one AP (wlan1, 5GHz) and one uplink (wlan0) — removing the current
-  tradeoff where away-from-home uploads run over the weak onboard radio.
-- **Considerations**:
-  - Both dongles share the Pi 3's USB 2.0 bus (~480 Mbps total), so two AC dongles can't both
-    run at full speed simultaneously — but each still far exceeds the onboard radio.
-  - Power: two AC dongles draw more than onboard + one; verify the 5V GPIO feed holds
-    (`vcgencmd get_throttled` should stay `0x0` for no undervoltage).
-  - Interface naming: both radios are USB now, so `wlan0`/`wlan1` may not map predictably —
-    pin `connection.interface-name` and/or add MAC-based udev rules so AP vs uplink never swap.
-  - The rtl88x2bu driver is already built; a second identical dongle should be plug-and-play.
+- **Status**: `SHIPPED` 2026-08-14
+- **Area**: hardware + `deploy/yaris_uplink.py`, `deploy/install_netwatch.sh`, `modules/app_network.py`, `deploy/90-yaris-uplink`
+- **Phase**: Phase 29
+- **What**: Owner added a second TP-Link Archer T3U (RTL8812BU) to replace the onboard
+  BCM43438 as the internet uplink. Both radios are now AC1300 T3U dongles — `wlan1` (T3U #1)
+  hosts the 5GHz in-car AP, `wlan2` (T3U #2) carries the uplink (home-wifi + phone-hotspot),
+  and the onboard `wlan0` is retired to a weak fallback. Removes the old tradeoff where
+  away-from-home uploads ran over the weak onboard radio.
+- **Changes**: `PRIMARY_INTERFACE=wlan2` / `FALLBACK_INTERFACE=wlan0` / `AP_INTERFACE=wlan1`
+  in `yaris_uplink.py` + `app_network.py`; `install_netwatch.sh` rebinds `home-wifi` +
+  `phone-hotspot` to wlan2 and recreates the `home-wifi-fb` fallback on wlan0; the NM
+  dispatcher (`90-yaris-uplink`) now listens on `wlan0|wlan1|wlan2`.
+- **Verified**: the second T3U enumerates as `wlan2` (rtl88x2bu) and
+  `vcgencmd get_throttled` = `0x0` (no undervoltage with both dongles powered).
+- **Open item**: interface-name pinning relies on USB enumeration order; if the two T3Us ever
+  swap ports, `wlan1`/`wlan2` swap — a MAC-based udev/`.link` rule is the robust follow-up.
 
 
 ### FEAT-15 — Clear DTC codes from the DTC page
diff --git a/PLAN.md b/PLAN.md
index 8125797..e54e46a 100644
--- a/PLAN.md
+++ b/PLAN.md
@@ -12,14 +12,13 @@ pick up the project without needing prior chat history.
 - **Board**: Raspberry Pi 3 Model B Rev 1.2, 906MB RAM. Confirmed too weak to run an AI coding
   agent — all agent-assisted dev work happens on a separate local machine; the Pi is only used
   for hardware bring-up/testing/deployment via SSH (`yaris@<pi-ip>`).
-- **WiFi**: Dual-radio setup — **TP-Link Archer T3U (RTL8812BU)** USB dongle as `wlan1` and the
-  onboard BCM43438 as `wlan0`. **2026-08-12 role swap**: the fast T3U now hosts the in-car AP
-  ("vroom vroom yaris de course" on 5GHz at 10.42.0.1) for fast phone access (Android dev, video
-  browsing); the weak onboard radio carries the internet uplink (home WiFi "BuzzBis" +
-  phone hotspot, static IP 192.168.50.220, gw 192.168.50.1). Both radios active simultaneously.
-  Tradeoff: away-from-home uploads (dashcam/trip sync) now run over the weak onboard radio — a
-  background task, accepted by owner. A single radio cannot be AP + client at once, so the
-  phone-hotspot uplink cannot also live on wlan1 while it hosts the AP.
+- **WiFi**: **Dual T3U** setup (2026-08-14, FEAT-14) — two TP-Link Archer T3U (RTL8812BU)
+  dongles: `wlan1` hosts the in-car AP ("vroom vroom yaris de course" on 5GHz at 10.42.0.1)
+  and `wlan2` carries the internet uplink (home WiFi "BuzzBis" + phone hotspot, static IP
+  192.168.50.220, gw 192.168.50.1). The onboard BCM43438 (`wlan0`) is retired to a weak
+  fallback. Away-from-home uploads (dashcam/trip sync) now run on a fast AC radio. A single
+  radio cannot be AP + client at once, so the phone-hotspot uplink cannot live on wlan1 while
+  it hosts the AP.
 - **GPS/GSM**: Waveshare **SIM868 GSM/GPRS/GNSS/Bluetooth HAT**. GNSS provides live GPS fixes
   (confirmed working, ~7 satellites, ~80s cold-start TTFF). GSM/GPRS cellular is **not in use**
   (no SIM card available); a Huawei **E3372h-153 4G LTE modem** has been purchased as a future
diff --git a/app.py b/app.py
index e38efef..eb14a65 100644
--- a/app.py
+++ b/app.py
@@ -131,7 +131,7 @@ def uplink_connect():
         return jsonify(error=str(error)), 503
     return jsonify(status="connection_requested"), 202
 
-_HOTSPOT_PROFILE = "Hotspot-local"  # wlan0 AP profile name in NetworkManager
+_HOTSPOT_PROFILE = "Hotspot-local"  # AP profile name in NetworkManager (hosted on wlan1)
 
 
 @app.route('/api/hotspot')
diff --git a/deploy/90-yaris-uplink b/deploy/90-yaris-uplink
index 3d86591..73084a5 100644
--- a/deploy/90-yaris-uplink
+++ b/deploy/90-yaris-uplink
@@ -1,7 +1,7 @@
 #!/bin/sh
 
 case "$1" in
-    wlan0|wlan1) ;;
+    wlan0|wlan1|wlan2) ;;
     *) exit 0 ;;
 esac
 
diff --git a/deploy/install_netwatch.sh b/deploy/install_netwatch.sh
index 3aad479..52457b6 100755
--- a/deploy/install_netwatch.sh
+++ b/deploy/install_netwatch.sh
@@ -7,15 +7,15 @@
 # already exist (see PLAN.md Phase 6). The optional "phone-hotspot" profile is
 # created through the Settings page.
 #
-# Since 2026-08-12: the fast TP-Link T3U (wlan1) hosts the in-car AP
-# ("Hotspot-local"), while the onboard BCM43438 (wlan0) carries the internet
-# uplink (home-wifi / phone-hotspot).
+# Since 2026-08-14 (FEAT-14): dual T3U — wlan1 (T3U #1) hosts the in-car AP
+# ("Hotspot-local"), and a second T3U (wlan2) carries the internet uplink
+# (home-wifi / phone-hotspot); the onboard BCM43438 (wlan0) is the fallback.
 set -euo pipefail
 
 REPO_DIR="$(cd "$(dirname "${BASH_SOURCE[0]}")/.." && pwd)"
-WLAN=wlan0   # onboard — internet uplink
-WLAN_FB=wlan1  # T3U — uplink fallback
-AP_IFACE=wlan1 # T3U — hosts the in-car AP
+WLAN=wlan2    # T3U #2 — internet uplink
+WLAN_FB=wlan0 # onboard BCM43438 — uplink fallback
+AP_IFACE=wlan1 # T3U #1 — hosts the in-car AP
 
 sudo systemctl stop yaris-uplink-wait.service 2>/dev/null || true
 sudo systemctl stop yaris-netwatch.timer yaris-netwatch.service 2>/dev/null || true
@@ -28,9 +28,9 @@ sudo install -m 644 "$REPO_DIR/deploy/yaris-hotspot-dns.conf" \
 sudo install -m 755 "$REPO_DIR/deploy/90-yaris-uplink" \
     /etc/NetworkManager/dispatcher.d/90-yaris-uplink
 
-# Bind the internet uplink to the onboard radio (wlan0)
+# Bind the internet uplink to the second T3U (wlan2)
 sudo nmcli connection modify home-wifi connection.interface-name "$WLAN"
-# The in-car AP lives on the fast T3U (wlan1), forced to 5GHz
+# The in-car AP lives on T3U #1 (wlan1), forced to 5GHz
 sudo nmcli connection modify Hotspot-local \
     connection.interface-name "$AP_IFACE" \
     802-11-wireless.band a \
@@ -44,8 +44,8 @@ if nmcli connection show phone-hotspot >/dev/null 2>&1; then
         802-11-wireless.mtu 1400
 fi
 
-# Create wlan1 fallback profile (lower autoconnect-priority so wlan0 wins)
-# home-wifi-fb: same SSID as home-wifi but on wlan1 (T3U)
+# Create wlan0 fallback profile (lower autoconnect-priority so wlan2 wins)
+# home-wifi-fb: same SSID as home-wifi but on wlan0 (onboard)
 HOME_SSID=$(nmcli -g 802-11-wireless.ssid connection show home-wifi 2>/dev/null || true)
 HOME_PSK=$(sudo nmcli -g 802-11-wireless-security.psk connection show --show-secrets home-wifi 2>/dev/null || true)
 if [ -n "$HOME_SSID" ] && [ -n "$HOME_PSK" ]; then
@@ -62,7 +62,7 @@ if [ -n "$HOME_SSID" ] && [ -n "$HOME_PSK" ]; then
     echo "Created home-wifi-fb fallback on $WLAN_FB"
 fi
 
-# Re-enable wlan0 as a managed (but low-priority) fallback
+# Re-enable wlan0 (onboard) as a managed low-priority fallback
 sudo nmcli device set "$WLAN_FB" managed yes 2>/dev/null || true
 
 sudo cp "$REPO_DIR/deploy/yaris-netwatch.service" /etc/systemd/system/yaris-netwatch.service
diff --git a/deploy/readme.md b/deploy/readme.md
index 900b789..ae2eb6c 100644
--- a/deploy/readme.md
+++ b/deploy/readme.md
@@ -20,7 +20,7 @@ cd /home/yaris/app/yaris-obd
 
 # REQUIRED before netwatch install:
 # Create/update NetworkManager profiles named exactly:
-#   - home-wifi      (client WiFi → wlan0, the internet uplink)
+#   - home-wifi      (client WiFi → wlan2, the internet uplink)
 #   - Hotspot-local  (local AP, shared at 10.42.0.1/24, on wlan1)
 # See section 4 below for exact nmcli commands.
 
@@ -42,10 +42,10 @@ curl -I http://127.0.0.1/
 
 ## TP-Link Archer T3U (RTL8812BU) driver
 
-This project expects the T3U USB adapter as `wlan1` for the in-car AP (5GHz)
-and the onboard radio as `wlan0` for the internet uplink (home WiFi + phone
-hotspot). On a fresh Pi, install the RTL8812BU DKMS driver before configuring
-WiFi profiles:
+This project expects two T3U USB adapters — `wlan1` for the in-car AP (5GHz)
+and `wlan2` for the internet uplink (home WiFi + phone hotspot); the onboard
+`wlan0` is a fallback. On a fresh Pi, install the RTL8812BU DKMS driver before
+configuring WiFi profiles:
 
 ```bash
 sudo apt-get update
diff --git a/deploy/yaris_uplink.py b/deploy/yaris_uplink.py
index b542907..aed0e84 100644
--- a/deploy/yaris_uplink.py
+++ b/deploy/yaris_uplink.py
@@ -12,12 +12,12 @@ import uuid
 PHONE_CONNECTION = "phone-hotspot"
 HOME_CONNECTION = "home-wifi"
 AP_CONNECTION = "Hotspot-local"
-# 2026-08-12 swap: the fast TP-Link T3U (wlan1) hosts the in-car AP so phones
-# get 5GHz AC throughput; the weak onboard BCM43438 (wlan0) carries the
-# internet uplink (home-wifi / phone-hotspot), which is background traffic.
+# 2026-08-14 (FEAT-14): dual T3U — wlan1 (T3U #1) hosts the in-car AP so phones
+# get 5GHz AC throughput; a second T3U (wlan2) carries the internet uplink
+# (home-wifi / phone-hotspot); the onboard BCM43438 (wlan0) is only a fallback.
 AP_INTERFACE = "wlan1"
-PRIMARY_INTERFACE = "wlan0"    # onboard — internet uplink
-FALLBACK_INTERFACE = "wlan1"   # T3U — uplink fallback if onboard is absent
+PRIMARY_INTERFACE = "wlan2"    # T3U #2 — internet uplink
+FALLBACK_INTERFACE = "wlan0"   # onboard BCM43438 — fallback if T3U #2 is absent
 STATUS_PATH = "/var/lib/yaris-obd/uplink-status.json"
 PHONE_KEYFILE = (
     "/etc/NetworkManager/system-connections/"
@@ -224,7 +224,7 @@ def _ap_client_count():
 
 
 def check_uplink():
-    """Manage internet uplink on wlan0 only. wlan1 AP is never touched."""
+    """Manage internet uplink on the uplink interface only. wlan1 AP is never touched."""
     current = active_connection()
     phone_configured = connection_exists(PHONE_CONNECTION)
 
@@ -275,7 +275,7 @@ def check_uplink():
             return True
         return _connect_home_or_idle()
 
-    # Phone not configured. Home wifi is the only uplink on wlan1.
+    # Phone not configured. Home wifi is the only uplink.
     if current == HOME_CONNECTION:
         write_status("home_connected_no_phone")
         return True
diff --git a/modules/app_network.py b/modules/app_network.py
index 29cc0be..b8f6871 100644
--- a/modules/app_network.py
+++ b/modules/app_network.py
@@ -9,10 +9,10 @@ BASE_DIR = os.path.dirname(os.path.dirname(os.path.abspath(__file__)))
 INSTALLED_HELPER = "/usr/local/bin/yaris-uplink"
 REPO_HELPER = os.path.join(BASE_DIR, "deploy", "yaris_uplink.py")
 PHONE_CONNECTION = "phone-hotspot"
-# 2026-08-12 swap: onboard (wlan0) carries the internet uplink; the fast
-# T3U (wlan1) hosts the in-car AP.
-PRIMARY_INTERFACE = "wlan0"
-FALLBACK_INTERFACE = "wlan1"
+# 2026-08-14 (FEAT-14): dual T3U — wlan1 (T3U #1) hosts the in-car AP; the
+# second T3U (wlan2) carries the internet uplink; onboard wlan0 is a fallback.
+PRIMARY_INTERFACE = "wlan2"
+FALLBACK_INTERFACE = "wlan0"
 AP_INTERFACE = "wlan1"
 STATUS_PATH = "/var/lib/yaris-obd/uplink-status.json"
 
diff --git a/readme.md b/readme.md
index 56e1f2c..c4ff71c 100644
--- a/readme.md
+++ b/readme.md
@@ -37,8 +37,8 @@ Dashboard — mobile (390 px) and desktop (1280 px):
   can be cleared straight from the DTC page.
 - **Real GPS tracking** — Waveshare SIM868 GNSS HAT with GPIO PWRKEY auto-power-on. Live position
   plotted on an offline Leaflet map (pre-cached tiles, no internet needed).
-- **WiFi hotspot** — fast 5GHz in-car AP on the T3U (wlan1), internet uplink (home WiFi +
-  phone hotspot) on the onboard radio (wlan0). SSID/password configurable from the Settings page.
+- **WiFi hotspot** — fast 5GHz in-car AP on a T3U (wlan1), internet uplink (home WiFi +
+  phone hotspot) on a second T3U (wlan2); the onboard radio is a fallback. SSID/password configurable from the Settings page.
 - **Dashcam workflow** — auto-detects any USB dashcam, mounts read-only, browses files before
   importing. Import one, selected, or all files. Delete individual or all files directly from the
   dashcam. Verified against real 28GB/87-file hardware.
@@ -79,8 +79,8 @@ Dashboard — mobile (390 px) and desktop (1280 px):
 | Raspberry Pi 3 Model B Rev 1.2 | Web UI host, logger, uploader, and WiFi hotspot |
 | Waveshare SIM868 HAT | GNSS (GPS) + optional GSM/GPRS uplink, unused Bluetooth |
 | USB OBD-II adapter | PL2303-based, ELM327-compatible (originally Bluetooth, switched to USB) |
-| TP-Link Archer T3U (RTL8812BU) | USB WiFi dongle — AC1300 dual-band. Hosts the 5GHz in-car AP (wlan1) since 2026-08-12 |
-| Onboard BCM43438 (wlan0) | Internet uplink (home WiFi + phone hotspot) since 2026-08-12 |
+| 2× TP-Link Archer T3U (RTL8812BU) | USB WiFi dongles — AC1300 dual-band. wlan1 hosts the 5GHz in-car AP; wlan2 carries the internet uplink since 2026-08-14 |
+| Onboard BCM43438 (wlan0) | Fallback only — was the internet uplink until 2026-08-14 |
 | USB dashcam | Any brand — detected as generic USB mass storage |
 | 2013 Toyota Yaris | The patient |